Operators Manual

Driveshaft rack GS-WAL5-150 – Item number: 1697110

Bild 5

  • Position 1: Side panel Driveshaft rack
  • Position 2: Intermediate plate-WAL Driveshaft rack
  • Position 3: Intermediate plate-CIC Driveshaft rack
  • Position 4: Intermediate plate PTO Driveshaft rack
Figure 1

Figure 1

[bws_pdfprint_pagebreak]

Slide the bottom intermediate plate with the lettering “COMER INDUSTRIES CORPORATION” (position 3) and the side panels (position 1) vertically into each other. The parts should be placed at the right angles and aligned with each other at the slots (see Fig. 2 and Fig. 3).

Fig. 2 and Fig. 3

Fig. 2 and Fig. 3

Slide 2 intermediate plates designed to store small parts (position 4) horizontally and parallel into the side panels (see Fig. 4).

Fig. 4

Fig. 4

Slide the intermediate plate at the top with the lettering “WALTERSCHEID” (position 2) crosswise and at right angles to each other vertically into the slots (see Fig. 5).

Fig. 5

Fig. 5

Insert the clamping screws with the hook into the lower hole of the side panel (see Fig. 6).

Fig. 6

Fig. 6

Fit the snap hook of the tensioning cable to the hole in the top of the side panel (see Fig. 7) and connect it to the open hook of the tensioning cable. Position the tensioning ropes crosswise (see Fig. 8).

Fig. 7 and Fig. 8

Fig. 7 and Fig. 8

Tighten the tensioning screws evenly and tension the tensioning cables (see Fig. 9).

Fig. 9

Fig. 9

Cut the edge protection profile to match the length of the side parts of the support surfaces and adjust (see Fig. 10).

Fig. 10

Fig. 10

  • Attach the supplied type plate in the lower area of the drive shaft rack to the holes provided using rivets.
  • During the development of the drive shaft rack, great importance was dedicated to designing a modern, innovative and cost-effective product. Galvanized sheet steel was chosen, which is shaped by laser cutting accordingly. Over a long period of use, this can lead to slight rusting of the cut edges (primarily, but not exclusively, on the contact surfaces). If necessary, this can be removed by simple manual mechanical processing and covered with commercially available corrosion protection agents.
  • The surface must not be cleaned with steel wool or other metal brushes, as these will scratch the steel surface. Also avoid contact with caustic (corrosive) materials such as powder. They can damage the surface and lead to rust formation. Use a soft sponge or cloth to wipe off fingerprints or dust deposits.
  • Stubborn stains can also be removed with mild soap or washing-up liquid and warm water. After cleaning, wipe thoroughly and dry.
  • When equipping the drive shaft stand, ensure that the load is evenly distributed. Dabei dürfen folgende Belastungsgrenzen nicht überschritten werden: – Lagerung Gelenkwellen bis 30 kg/St – Belastung Fachboden-Zwischenplatte je 10 kg

[bws_pdfprint_pagebreak]

Safety instructions

Important / Exclamation mark

Important:

To avoid injury, protective gloves, safety glasses and safety shoes must be worn during all dismantling/ assembly actions described in this chapter.

Important / Environmental protection

Environment:

Lubricants can enter the environment. Environmental pollution: Collect, store and correctly dispose of lubricants in suitable containers.

Important / Exclamation mark

Important:

Use only original Walterscheid spares when replacing parts. If the vehicle owner does not have the appropriate skilled workers and the necessary technical equipment, the replacement may only be performed by a specialist workshop.

The checks must be carried out at the appropriate intervals in order to prevent damage to the coupling.

Note:

The entire tensioning of the PTO shaft stand should be checked regularly for tightness depending on the load. This can be done, for example, as part of regular safety inspections.

We recommend a weekly visual inspection of the drive shaft stand based on the regulations for the regular inspection of racks.

We recommend the use of a visual inspection checklist with the following points:

Prüfung auf erkennbare Verformungen und Beschädigung Prüfung der Standfestigkeit (Kippsicherheit) und gleichmäßige Beladung Prüfung der Befestigungselemente Prüfung auf Einhaltung der Sicherheitsabstände

To the product Further documents
  • Document Name:
  • pto-a-1697110-en
  • Operating instructions Driveshaft rack GS-WAL5-150
  • Document type:
  • Assembly and Instruction Guide
  • Language versions:
  • German
  • Manual for Walterscheid item numbers:
  • 1697110
  • As of:
  • 08.04.2024

Related documents